$9.14 - $25.08
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)
Prevents handlebar and front wheel from rotating or moving when the bike be stored or fixed.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
Bontrager's Universal Repair Stand Adapter safely holds your Trek Madone road bicycle in a traditional workstand (sold separately). It securely holds your bike in any clamp-style or screw-type repair stand. This universal adapter has replaceable inserts to accommodate different mast caps and adapters for the 2008 and 2010 Madones.
The PCS-EXT is an extension that adds up to 21 inches (53 cm) of adjustable working height to any PCS-1 or PCS-4 repair stand manufactured between June 1996 and December 2001. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC Accessory Collar.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
For anyone who doesn’t want to be confined to parking lots or trailheads — adventurers, racers, and garage mechanics — Küat designed the Tri-Doc for you. Tri-Doc offers an affordable way to turn your NV 2.0 into a travel stand. Reliable tri-leg design creates a stable platform for needed tune-ups or repairs. Aluminum construction finished with polished anodizing pairs perfectly with your NV 2.0. - Portable telescoping design - Quick setup - Pairs with your NV 2.0 Trail Doc - Anodized finish reflects NV 2.0 - Rubber feet offer additional stability and protection
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
- Home mechanic portable repair stand - Sturdy tubular steel design - Folding design for compact storage and mobility - Height adjustable from 36—72" (91—183cm) - V-Box clamping jaws with quick-dial closure (26.8mm+ tube diameters) - Detachable tool organizing tray - Maximum capacity: 55lb (25kg)
- Designed to be easily mounted to post, wall, bench and flat surface. - Adjustable linkage clamp allows the bike positioned at any angle. - Max load: 30 kg.
Have you ever wondered why all Feedback Sports bike repair stands have exposed frame above the clamp head? Our Pro Truing Stand is designed to sit atop all of our portable stands! The truing stand also includes a free-standing steel base and a bench-mount adapter for when you're not traveling to races and top-secret trailheads. This single-arm, precision wheel and rotor truing stand is awesome at home and excels at races, events, or adventure-riding weekends. And with the all-new Thru-Axle Adapter, it can accommodate the most common wheel sizes for quick-release or thru-axle hub designs. Use the benchtop mount for an awesome tubeless setup and tubular gluing station. - All-New Thru-Axle Adapter accommodates: 10mm, 12mm, 15mm and 20mm – up to 157mm wide hubs (SuperBoost) - Single-arm design is lightweight, portable and compatible with most wheel systems - Precision spring-loaded tip can verify lateral and radial rollout - Measurement arm includes a disc brake rotor truing slot - Steel base measures 10.25 x 8.5-inches (26.5 x 21.5cm) and 5.8lbs (2.6kg) - Bench mount measures 4 x 6-inches (10.1 x 15.2cm) - Anodized 6061 T6 aluminum construction is ultralight, corrosion resistant and incredibly durable - Can accommodate up to 29-inch wheel with tire mounted - 9mm quick-release hubs use quick-release for mounting - 12mm, 15mm and 20mm thru-axle adapter included - 3-Year Warranty
Hirobel is a specially designed clamp for bicycle repair stands that makes it easier to work on your bike. It better distributes stresses and loads through the bicycle frame, offering superior stability while eliminating possible crushing or damage to thin-walled and shaped tubing. The pressure clamps used on contemporary workstands were developed for round steel tubing more than 40 years ago, predating carbon fiber, aluminum, aerodynamic and oversized tube shapes, integrated seat masts, dropper posts, and suspension systems. These legacy designs assume your bicycle tubing to be both round and straight, and when it is not, the clamp can impart very high point loads at the clamp edges causing finish damage, internal carbon layup damage, or outright crushing of tubes on the lightest designs. With Hirobel, specially shaped, paint-friendly cones and bindings cradle the frame at the tube intersections, where wall thicknesses are higher and forces can be distributed over much larger surface areas. Adjustable and adaptable for any possible frame design, the Hirobel also allows the repair stand clamp to be located closer to the bicycle center of gravity. This improves stability and eliminates bouncing of the bike during heavier work while also locating the drivetrain consistently higher for the mechanic, improving visibility while reducing back strain.
- Clamp height adjusts from 41.75"- 56.75" (106 to 144 cm) to allow you to work at a comfortable level - Clamp head rotates 360° - The articulating jaw on the clamp provides a large clamp opening, allowing the bike to be easily inserted and removed by flipping the cam lever. - Clamp head is micro-adjustable to accommodate various tube sizes. - No tools required for quick setup and storage - Lightweight aluminum construction - Product Weight: 13.6 lbs (6.18 kg) - Max load capacity: 77 lbs (35 kg)
A bench-mounted version of our popular PCS-10.2 Deluxe Home Mechanic Repair Stand. Features our world-famous cam-actuated micro adjust clamp design, which securely holds bicycles in place while allowing quick installation and removal. - Cam actuated, micro-adjustable clamp allows quick entry and exit and fits 1-inch to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material - Narrow clamping jaws (2.7-inch/7cm) fit into tight areas or on short seat posts - 360° infinite clamp rotation allows bike to placed in optimal position for specific repairs - All-steel structure for maximum stiffness and durability - Super strong glass-filled nylon-composite fittings and top tube internals enable smooth rotation and secure positioning - Mounts to any flat surface (mounting bolts not included) Distance from the center of the clamp to the center of the mount is approximately 11 3/4-inch (30cm). Height from bench to center of the clamp axis is approximately 9 7/8-inch (25cm). Weight Limit: The PCS-12.2 Home Mechanic Bench Mount Repair Stand has an 80 lb. (36kg) weight limit, provided the stand is securely mounted with appropriate fasteners to a solid and secure bench surface. The user is responsible for making sure the workbench and the fasteners are capable of handling this amount of weight.
- Clamp can be positioned at 5 directions. - Adjustable in height, 105 - 150 cm. - Max load: 50 kg
Being a "shade tree mechanic" doesn't mean you should lean your bike against a tree. You paid hard-earned money for your family's bike collection and we've got a budget-conscious, yet feature-loaded bike repair stand that's perfect for the home bike mechanic. The price-point leading 360-degree rotating clamp can position your bike optimally for any work you're planning. Plus, the Recreational Stand leverages a 52-inch (132cm) wide base with rubber-coated end caps for fantastic stability on any surface. And when the service day is done, it folds into a space-saving unit for storage. Add a Tool Tray, Bottle Opener and a Pro Truing Stand for the complete at-home bike shop. - Seatpost clamp features Spinner Knob for quick closure and precision clamping pressure - 360-degree rotating clamp design provides easy access to any part of your bicycle - Fixed clamp height at 55-inch (139cm) - Rubber-coated clamp secures and protects expensive components and beautifully painted frames - Clamp opening up to 1.9-inch (4.8cm) accommodates even the largest diameter frame tubes - Powder-coated steel construction is corrosion resistant and incredibly durable - Stiff 52-inch (132cm) base and rubber-coated end caps create ultimate stability even on uneven surfaces - Total load capacity of 60lbs (27.2kg) accommodates service on most road, mountain bikes, fitness bikes, and electric bikes - Portable and compact construction creates a remarkably small folded footprint of 10 x 4 x 55-inches (25.4 x 10.2 x 139.7cm) - Optional Travel Bag available - At 13.8lbs (6.3kg), moving in and out of storage is no problem - No assembly required - 3-year Warranty
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
After years of research and testing, Park Tool's built what they consider the best shop clamp made. It’s smooth, versatile and built to stand up to everyday shop use. • #100-3D fits the following repair stands: PRS-2, PRS-2 OS, PRS-2 OS-1, PRS-2 OS-2, PRS-3, PRS-3 OS, PRS-3 OS-1, PRS-3 OS-2, PRS-3.2-1, PRS-3.2-2, PRS-4, PRS-4 OS, PRS-4 OS-1, PRS-4OS-2, PRS-4W and PRS-33 • #100-5D fits PCS-4, PRS-7, some models of PRS-5 (with composite top tubes), and PCS-1 models manufacturer post 2002. (Note: Inspect top tube below lever for an embossed "939") • #100-25D fits PRS-25, PCS-10, PCS-11, PCS-12 (and PRS-15 with 1951-15 Adaptor Stud) • Grips nearly any tube from 7/8” to 3” (23–76mm), including aero tubes • Micro-adjustability allows perfect clamping pressure every time and prevents damage to thin-walled tubes • Long travel cam handle allows quick entry, adjustment and exit • Versatile: It grips nearly any tube including aero shaped tubing and seat posts 7/8” to 3” (23mm-76mm). Its narrow clamping jaws (2.7”/7cm) are designed to clamp securely yet fit into tight areas or on short seat posts. • Durable, replaceable jaw covers • Soft Touch saddle cradle provides a perfect spot to temporarily rest a bike by its saddle • Built to last: Powder coated, precision machined, die-cast aluminum main body parts and high quality small parts • Fast operation: Cam-actuated adjustment system for quick entry, adjustment and exit, plus handy “spinner” handle helps speed large size range adjustments
Park's Bench-Mount Repair Stand easily bolts to any workbench and includes Park's shop-quality Micro-Adjust Clamp that handles round and aero seatposts and frames from 7/8-inch to 3-inches in diameter and clamps securely with its quick-release cam and handle that fine-tunes the tension. The clamp also has protective rubber jaws and built-in slots for cables. Plus its jaws are only 2.7 inches tall so they easily fit in narrow areas like on seatposts that aren't raised much. This stand rotates 360 degrees for optimum bike positioning, too.
"The PCS-9.3 is a basic folding bicycle workstand designed and built for the home mechanic – a stable way to hold nearly any bike off the ground for adjustments, cleaning and repair. Features 18"" (460 mm) of height adjustment and 360 degrees of clamp rotation, positioning all parts of the bike within reach for any mechanic whether seated or standing. The stand's all-steel construction with teardrop-shaped tubing ensures maximum rigidity and stability, with a locking support yoke and upgraded internals for extra dependability. The PCS-9.3 is able to hold up to 80 lbs. (36 kg), which allows for compatibility with virtually all two-wheeled pedal-driven bicycles, including fat bikes and most e-bikes.* The PCS-9.3 quickly folds down for storage and transport with a smooth-operating leg support system that pulls both legs up in one simple motion. The PCS-9.3 is the perfect way to upgrade your home shop. NOTE: The maximum weight capacity of the PCS-9.3 assumes the weight is centered below the clamp and between the legs.? - Fully adjustable clamp fits 7/8"" to 3"" (22 mm–76 mm) diameter tubes and seat posts of any shape and material, including aero posts and dropper posts - Narrow clamping jaws (2.7""/70 mm) fit into tight areas or on short seat posts - Durable textured powder coat finish - Maximum weight capacity: 80 lbs. (36 kg) - Height adjustable from 39"" to 57"" (990 mm–1450 mm) - Base when open forms a triangle of 36"" x 36"" x 48"" (920 mm x 920 mm x 1210 mm) - Folds down to 44"" x 14.5"" (1140 mm x 370 mm) - Weight: 16 lbs. (7.2 kg) - #2848A quick-release collar with accessory pods required for use of PTH-1 Paper Towel Holder or 106 Work Tray"
Page 1 of 3 Next page